How to Connect Multiple LED Strip Lights Using a Smart Controller

You can connect multiple LED strip lights together by using a smart controller. This type of circuit is much simpler and less complicated to install. Before you begin, you must calculate the total wattage of the lights. If you are using high-brightness LED strips, you should use special connector wires. You can cover soldered joints with electrical tape or heat shrink to protect them from damage. To connect multiple LED strips together, you must make sure that each one is wired to a separate outlet.

Parallel circuits are easier to install

When using LEDs, you have two basic wiring options: series and parallel. Series connections are connected in series and use three or four LEDs to supply power. Parallel wiring uses multiple groups of LEDs connected in parallel, allowing them to be switched in series or parallel. There are advantages and disadvantages to each wiring option. Learn about each and which one is right for you! Parallel wiring is recommended for multiple strip lights, however.

Because parallel wiring is easier to install, you can add more gadgets without affecting voltage and current flow. This is much easier to achieve than series wiring, but you will need to follow industry standards and match the forward voltage of each diode. Once you have determined how many strips you’ll need, you’ll be able to get the most brightness for your money. You’ll be happy you did.

The main advantage of using parallel circuits is that you can keep all strips powered when one fails. This method is recommended for high-brightness LED strips. However, it can also be challenging to wire multiple strips in series and parallel. You should always use a power supply rated for more watts than you need. It may be difficult to install multiple LED strips if one of them doesn’t work properly.

The advantage of using parallel wiring over series is that you can connect more strips end-to-end, minimizing the chance of voltage drop. This way, you can save space in your home, as each strip will share the same voltage. Moreover, you’ll get a continuous current of light, which means your entire house will be bright and colorful. So, the parallel wiring option is the way to go when installing multiple LED strip lights.

How to Connect Multiple LED Strip Lights Using a Smart Controller

Calculating the total wattage

To calculate the total wattage of multiple LED strip lights, first determine how many strips you will be connecting together. Look at the manufacturer’s specifications table for the total wattage of multiple strips. There are two basic types of LED strip lights: single-density and high-density. Single-density strips have fewer than nine LEDs per foot. High-density strips contain 18 or more LEDs per foot.

LED strips are measured in lumens per meter or foot. Good quality strips can provide up to 1500 lumens per meter. If your strips are lower in wattage, it does not mean you will use less power, and you need to have a power supply that can handle the total wattage. However, you should leave a 20 percent margin of safety when running multiple LED strips.

Next, you should know the voltage and current of LEDs. Determine the voltage using a multi-meter. If you do not have a multimeter, find the value of the LED’s forward voltage online. You may need to make a unit conversion to calculate the actual power usage. If you have a multimeter, a standard watt is 1000 milliwatts, so a white LED will use 3.5 volts, a red LED will use 1.8 volts, and blue LEDs will use 3.6 volts.

LED strip lights are an energy efficient option for your lighting needs. Listed on the package, each strip has a Wattage and a Power Consumption. Power Consumption refers to the total electricity consumption per meter of LED strip lights. The more strips you connect, the higher the total electricity consumption. The same strips can be connected in series to prevent blending consumption. This way, you can ensure that your lights are not mixing together.

Remember that LED strips are a low-wattage product, so the higher the voltage, the lower the total wattage. If you’re planning to install multiple LED strips, make sure to use a heat sink to prevent them from melting. The difference in power consumption can be significant, especially if you’re using multiple lights. If you’re planning to install multiple LED strips, be sure to consult the manufacturer’s manual for proper electrical circuitry and voltage specifications.

Using a smart controller to connect multiple LED strips

You can use a smart controller to connect multiple LED strip lighting systems. This type of lighting system is capable of remote control and uses a receiver connected to the power supply and transformer for each strip. It is important to ensure that the voltage of the receiver matches the voltage of the strips. There are a few options when using a smart controller to connect multiple LED strip lights. A simple version is the LEDnet******.

This smart device works with most popular LED strips and has a dedicated app for controlling the lights. Most of these lights come with a remote control, but some require a separate hub for proper operation. To connect the lights with the hub, you must first download the app. Once the app is downloaded, you’ll be able to control the lights on the smart device. You can also use your voice to control the lights remotely.

Some smart light strips connect to a phone app through Bluetooth. These devices are more stable and easy to use than other types of control devices. You can even group them in a smart app. To get started, download the Magic Home App from the Apple Store or Google Play. There, you can set up a custom connection by selecting a desired number of strips to control. You can then set the app to turn on and off the lights to get the desired effect.

If you’re interested in controlling multiple LED strips, the InStyle LED controller is a great choice. This device allows you to adjust the brightness, color, and hue of multiple strips at the same time. The InStyle LED controller can be used to connect multiple strips wirelessly. They are equipped with a remote control, wall controller, and wifi app control. Unlike other control devices, the InStyle smart controllers are wireless and can be installed just about anywhere.

Also Read: The Ultimate Guide to Connecting LED Light Strips

While wiring multiple LED strips is not difficult, it is essential to choose the right connectors for the lights. You can connect different brands of LED strips in a series by using connectors or by soldering copper pads. The soldered connection can be protected with electrical tape and heat shrink. It’s best to buy LED strip lights from reputable manufacturers. This way, you can be sure they work with each other.

LED strips require a power source of more than 60W. If you connect too many strips to a single power source, you can damage the strips. It’s also important to use the same voltage source for all the strips. That way, you won’t experience voltage drop, causing dim LEDs. Also, make sure you cut the strips properly to avoid damage to the copper connections. If they’re too short, you’ll end up with a mess.